A full work apron with a bib, crossed back straps, three pockets cut from one piece, and one cord that fits anyone. Drafted by the USDA in 1944 and revised in 1952.
From the public record: Dresses and Aprons for Work in the Home, Farmers' Bulletin No. 1963, 1944, revised 1952.
Exactly as the USDA published it. Draw 1" squares on paper and copy each piece square by square.
The same apron with the gaps, errors and unclear parts of the 1952 sheet fixed. Each fix is listed with its reason.
The same apron with modern construction: bound curves, bar tacks, grommets, heavier cloth, and a cut file for a machine.
The draft
Material
1 1/2 yards of 36-inch goods. Half-inch seam allowance included. Cord about 1½ yards.
The 1952 text
This apron is adjustable to a man of any size; it offers good protection for shop or jobs about a home. A woman might also like one of these aprons. Made of shower-resistant, washable cotton, it’s ideal for washday or dirty or wet work. Two long darts—one on each side—give the apron the shape that’s needed. Shoulder straps are fitted and sewed at center back to keep them from sliding. One piece of cloth makes the three pockets, which may be partitioned as desired.
To make the pattern: Draw 1-inch squares both ways on wrapping paper or newspaper. If you use newspaper, draw lines with colored pencil. Count squares and block the pattern pieces on exactly as shown here.
Cut the apron from 1½ yards of preshrunk, colorfast goods.
To make the apron: Baste hems on sides of the shoulder straps. Lap straps at center back. Turn raw edges in. Insert a loop for the cord at lower point, then double stitch the edges.
Stitch darts in the apron. Face the bib, then hem apron edges in the same way as the straps. Insert a loop for the cord at each corner in the back. Hem three top edges of pocket piece. Turn under sides and lower edge. Sew to apron and stitch to form partitions.
Make a drawstring—about 1½ yards long—longer if the man who wears it prefers aprons tied at front. For a tie, use cloth turned in and stitched or use cord. Run tie through three loops as pictured and knot each end to keep it from pulling out.
What was fixed
Bib facing did not match the bibThe 1952 facing is drawn about ⅜" narrower than the bib it faces at the armhole side, so it pulls the corner in. The facing is now traced from the bib’s own edge.Measured on the bulletin’s grid, page 13.
The pocket placement had no numbersThe bulletin shows the pocket only as a dashed line on the grid. Placement is now stated: pocket top centre 10⅝" below the bib top, top corners 3" either side of centre.Measured on the bulletin’s grid, page 13.
“Partitioned as desired” gave no partitionsDefault partitions are now drawn 4" either side of centre: an 8" middle pocket for a phone or notebook and two wide side pockets. Move them if you like.Our default. Graded when built.
A dashed line inside the pocket is never explainedThe bulletin draws a line 5⅜" down from the pocket’s centre top and never names it in the text. It is kept on the Original layer and marked as unexplained, not guessed at.Bulletin page 13; the text on the same page does not mention it.
36" goods are rare nowThe apron is drafted to fill the full 36" width (it measures 36½" across), so it only fits true 36" cloth with no selvage loss. Yardage is now worked out for today’s 45" and 60" goods.Common widths: 44/45" and 58/60" (sewcalcs.pages.dev/reference/fabric-widths).
No grain line, no hem widths, no dart orderGrain runs up and down each piece (parallel to the fold). Hems are the ½" allowance turned ¼" twice. Darts are sewn from the edge to the point, the last ½" right on the fold, threads tied, pressed toward the side.Standard practice; the bulletin’s own ½" allowance sets the hem.
Strap length is fixedThe cord adjusts the waist, but the straps are one length (about 17½"). Before cutting, hold a tape from the bib corner over the shoulder to the centre of the back; lengthen the strap at its lower end if it falls short.Our check. Graded when built.
Cut layout
Material
Goods
Buy
45" wide
1 1/2 yards
60" wide
1 1/2 yards
Plus 54" of cord. Yardage is a straight-line layout of every piece; nothing is folded or rotated.
Sewing
Cut every piece with its grain line parallel to the fold. Use the full-size cut file, or draw the 1" grid and block the pieces as in 1952.
Straps: turn the ½" allowance ¼" twice on both long sides and stitch. Lap the pointed ends at centre back as marked and stitch the lap twice.
Darts: stitch each from the edge to the point, last ½" on the fold, tie the threads, press toward the side.
Facing: sew the facing to the bib top, right sides together, ½" seam. Turn, press, stitch down.
Hem the armholes, sides and lower edge with the ½" allowance turned ¼" twice. Catch a loop in each back corner and at each strap’s lower point.
Pocket: hem the three top edges the same way, press the sides and bottom under ½", sew to the apron on the placement line, then stitch the two partitions.
Cord: 54" of cord or a turned strip, through the three loops, a knot at each end.
Bar tacks at every pocket stress pointPocket top corners and partition tops take the pull of every hand going in. A short bar tack at each spreads the load. Place it on the stress point, not over the edge, and keep the stitch density moderate: too dense punches the cloth.Seamwork, “Strong and pretty pockets”; US Patent 6,138,595 on pocket wear.
Bound edges instead of turned hems on the curvesA turned hem on a curve bunches. The bib top and armholes are bound with 1" cotton twill tape instead, and the cut file already trims the ½" hem allowance off those edges so the finished line stays where 1952 put it. The facing piece is deleted.Our change. Graded when built.
Webbing straps instead of cut strapsThe two cloth straps become 1" cotton webbing, each 18" long, crossed and stitched at centre back where 1952 lapped the points. Webbing needs no hemming and does not stretch, and taking the straps off the cloth brings the apron down to 1 yard of 60" duck, from 1½ yards.Yardage worked out by this page’s own layout. Graded when built.
Grommets instead of cloth loopsThree cloth loops become brass grommets at the two back corners and the strap ends. Three fewer pieces, nothing to fray.Our change. Graded when built.
Heavier clothCotton duck, 9 to 10 oz, instead of shower-resistant cotton. It is sold 58/60" wide, which this layout uses.60" cotton duck listings, e.g. Vogue Fabrics 9.3 oz.
A cut file for a machineEvery piece comes full size and unfolded as SVG and DXF in inches, for a plotter, a laser or a projector.Generated from the same numbers as the drawing.
Cut layout
Material
Item
Amount
Cotton duck, 9 to 10 oz, 58/60" wide
1 yard
Cotton twill tape, 1"
2 yards
Cotton webbing, 1"
1 yard
Brass grommets with washers
4
Cord
54"
Sewing
Cut the apron and pocket from 9 to 10 oz duck, 58/60" wide, using the cut file. No facing, no loops, no cloth straps.
Straps: cut two 18" lengths of 1" cotton webbing and seal the ends. Cross them at centre back and box-stitch the crossing. Set a grommet 1" up from each lower end.
Darts as in the Fixed layer.
Bind the bib top and both armholes in one run with 1" twill tape, folded over the raw edge, stitched close to the tape’s edge.
Hem the sides and lower edge, ½" allowance turned ¼" twice. Set a grommet in each back corner.
Pocket: hem the top edges, press the sides and bottom under, sew on, stitch the partitions, then bar tack the six marked points.
Cord through the four grommets, a knot at each end.
Dresses and Aprons for Work in the Home, Farmers' Bulletin No. 1963. Clarice L. Scott, Bureau of Human Nutrition and Home Economics, U.S. Department of Agriculture. 1944, revised 1952, pages 12 and 13, “Man’s Apron”. A work of the U.S. federal government, so it carries no copyright (17 U.S.C. 105).
The bulletin at the Internet Archive.
The 1952 grid was measured square by square from the scan, to about ⅛".
Changes marked “graded when built” have not been sewn and tested yet.